国产欧美一级一区二区三区,幻女一级毛片,亚洲日韩乱码中文字幕,免费久久久久久久精品成人欧美大片

<b id="1jzad"></b>
  • <b id="1jzad"></b>
  • <b id="1jzad"><address id="1jzad"><ol id="1jzad"></ol></address></b><b id="1jzad"></b>
      <u id="1jzad"><address id="1jzad"></address></u>
    1. 點擊這里給我發(fā)消息


      Mobile :+86 13937199140

      PRODUCT CATEGORY

      TCB-100A Matte White Ink of High Dyne Level

      來源: 發(fā)布時間:2019-04-17

      This printing ink is two component matte white glass ink of high dyne level, aiming at meeting the high requirements of the touch screen industry. The cured film has various advantages, such as good adhesion, water resistance, chemical resistance, printability, surface hardness and abradability.

      Scope of applications: common glass, tempered glass.

      Operation process: Add 1 portion of the TCB-100B hardener into 10 portions of this ink and dilute the mixture with moderate thinner, then print with the 350~420-mesh halftone.

      First coating: baking at 130℃ for 8 min;          Second coating: baking at 130℃ for 8 min;   

      Third coating: baking at 130℃ for 8 min;         Last coating: baking at 130~150℃ for 15~20 min.

      Technichal parameters are shown in the following table. 

      Test Items

      Test Methods

      Evaluation Criteria

      Fineness

      GB/T1724-79

      8μm

      Surface tension

      Application criterion of the dyne pen

      34dyn/cm

      Size change

      Quadratic element measuring instrument standard manufacture procedure (165S, 420 mesh printing)

      40μm

      Ultrasonic washing

      Ordinary detergent, 65, 2hr

      Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

      Boiling resistance

      Soaking in 100 deionized water for two hours

      Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

      High and low temperature humidity and heat cycle

      80, 95% RH (8hr); 40(2hr); ten cycles in total

      Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

      Hardness

      Mitsubishi Pencil at an angle of 45 degrees, 500-gram force, measuring at different locations for 3 times

      2H

      Adhesion

      Cutting 100 grids, 3M gummed paper, continuously pulling off for 5 times

      Cross-cut adhesion test, 100%

      Surface resistance

      Testing surface resistance at 5 locations (≤80%RH)

      1010Ohm

      Acid resistance

      Soaking in 25 5% H2SO4 solution for two hours

      Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

      Alkali resistance

      Soaking in 25 5% NaOH solution for two hours  

      Non-foaming;non-wrinkling;non-discoloring;cross-cut adhesion test, 100%

      Ethanol tolerance

      Tester loaded with 200 grams; using the winsey, dipped with over 99% alcohol, to rub back and forth for 100 times

      Colorfast; not tarnishing

      Solvent (Acetone) resistance

      Tester loaded with 200 grams; using the winsey, dipped with chemically pure acetone, to rub back and forth for 50 times

      Colorfast; not tarnishing

      Performance features:

      Its obvious predominance lies in environmental compliance, good surface tension, good thixotropic structure, medium drying speed

      and weak corrosion.

      Usage:

      ① Add 1 portion of the matching TCB-100B hardener into 10 portions of the ink and then fully stir the mixture with moderate thinner before printing.

       ② The recommended baking temperature is 130℃ and the recommended baking time is 15 min. On other conditions, please

      confirm the feasibility in advance in order not to affect the product quality.

      ② During the multilayer overprint, in order to ensure the quality, the first coating solidifies after baking at 130℃ for 8 min; the

      second coating solidifies after baking at 130℃ for 8 min; the last coating solidifies after baking at 130~150℃ for 15~20 min.

      ④ The selection of the thinner types and the thinner dosage depend entirely on the adjustment of printing mesh number,

      environmental condition and printing effect.

      Storage condition:

        Before and after using this series of ink, the ink containers should be kept completely sealed in cool and ventilated places to avoid

      exposure to open fire and high temperature.

      Guarantee period:

        The guarantee period is one year since the production date. Beyond the deadline, please reconfirm the usability.

      Note ①: All the above tolerance test data, derived from our test results, is for your reference only and not listed as guarantee value.

      Note ②: This series of ink meets the standard of RoHS2.0, REACH, Halogen and the total test data concerning eight heavy metals.